IndustrialConverter Solutions - Renewable

IndustrialConverter Solutions - Renewable

Solutions for the future of energy - products for solar and wind energy

Without doubt, wind and solar power plants are currently the cleanest form of energy and are now no longer considered as niche products but instead offer a real alternative to traditional methods of energy generation. Inverters are used in both wind and solar power installations and these achieve the highest efficiency ratings.

However, they do generate interference, which cannot be allowed onto the public mains network and is controlled by power quality standards, so that other electrical equipment is not affected by these disturbances.

REO has 90 years of experience in the application of inductive and resistive components, over a wide range of products and has gained a broad know-how, in particular with respect to EMC and Power Quality issues for inverter drives.

Wind energy technology

In contrast to solar energy, energy obtained from wind power is AC. To comply to standards for grid connected inverters, certain criteria like network frequency, sinusoidal output voltages and other interference factors have to be satisfied as well as factors like variable energy generation (variations in wind intensity). In this application, the AC power is first converted into DC power with an inverter.

In order to adhere to standards of electromagnetic compatibility (EMC), several components — from line filters, HF transformers, HF storage chokes, compensation chokes, mains and motor chokes to sinusoidal and harmonic filters — are utilised. REO supplements this range with resistive components like brake resistances for protection from overload conditions.

Water cooling for maximum power in a small space

Wind energy plants are becoming progressively more compact in order to achieve the best possible return from the smallest possible area. A solution to this offer water-cooled components that enable optimized cooling in the smallest space . REO manufactures a wide range of devices with water cooling - a pioneering alternative to air cooling.

Solar technology

Solar systems first generate DC voltage from solar energy, then a solar inverter converts DC into AC voltages. Single-phase or three-phase inverters can be used depending on the power requirement and application.

The ever-increasing efficiency of energy conversion in modern inverters is resulting in high-frequency energy that is fed to the DC circuits. This fast switching of power semiconductors can then result in a premature ageing of the solar modules.

REO components – like filter chokes and DC EMC filters – counteract this safely and reliably to optimise the service life. For inverters which require transformers, REO produce highly efficient ring core based designs, EMC filters and components for interference suppression and safety and current transducers and shunt resistances for current monitoring.

For transformer-less inverters, REO manufactures ring core chokes, storage chokes, filter chokes and resonance chokes. Single-phase or three-phase sinusoidal filters are particularly suitable for sine-wave filtering.

We are always there to listen to your requirements - just give us a call!

 

  • CNW 107.3/480

    High-current mains filters (3 lines)

    CNW 107.3/480
    • Nominal Voltage: 480 V
    • Rated current: 280 - 3000 A

    Applications: Suppression of frequency inverters, Power electronics and general suppression for higher power ratings on wind energy and industrial applications.



    • Conforming to: VDE 0565-3 / IEC 950 / UL 1283

    • Test voltage: L-N 2100 V,DC 1s, L/N-PE 2700 V,DC 1s

    • Overload: 1,5 x I 1 min/h

    • Climatic category: DIN IEC 68 Teil 1 25/085/21

  • CNW 114/480

    Three-phase mains filters (3 lines)

    CNW 114/480
    • Nominal Voltage: 480 V
    • Rated current: 80 - 1200 A

    Applications: Frequency converters for motor drives, wind power installations and power supply units



    • Conforming to: VDE 0565-3 / IEC 950 / UL 1283

    • Test voltage: L-L 2100 V, DC 1s, L-PE 2700 V, DC 1s

    • Overload: 1,5 x I 1 min/h

    • Climatic category: DIN IEC 68 Teil 1 25/085/21

  • CNW 174

    DC filter for photovoltaik (2 lines)

    CNW 174
    • Nominal Voltage: 900 V
    • Rated current: 10 - 600 A

    Applications: The DC-filter surpresses grid-bound troubles of inverters for renewable energies like solar and wind power. 



    • Conforming to: VDE 0565-3/ IEC 950/ UL 1283

    • Test voltage: L-L 3000 V, DC 1 s; L-PE 3000 V, DC 1s

    • Climatic category: DIN IEC 60068-1

    • Overload: 1,5 x INenn 1 min / h

  • CNW 806

    Three-phase-dv/dt filter

    CNW 806
    • Nominal Voltage: 500 V
    • Rated current: 4 - 1200 A
    • Inductance: 0,005 - 1,5 mH

    Reduce voltage rice to < 500V/µs - electrical consumrs and insulation will protected with low costs. 


    A simple and inexpensive method for reducing the rate of voltage rise is to use a du / dt filter or throttle. It dampens the voltage rise to acceptable values and prevents overvoltages on long supply lines.


    Losses and heating are minimized and the leakage current reduced. By limiting the rate of voltage rise, the motor insulation is protected and thus prolongs the life.


    Also, the electromagnetic interference can be reduced in the radiation range of 1 MHz to 30 MHz.



    • Rated voltage: U ≤ 3 x 500 V

    • Reduce voltage rice to < 500V/µs

    • Field frequency: 0 - 60 Hz

    • Drive switching frequency: up to 150 A >4kHz, from 150 A >1,5KHz

    • According to: EN 60289 / EN 61558

    • Test voltage: L-L 2500 V, AC/50Hz 60s; L-PE 2500 V, AC/50Hz 60s

    • Insulation class: T40/F

    • Protection rating: IP00

    • Climatic categorie: DIN IEC 60068-1

    • Overload: 1,5 x INenn 1 min / h

    • Ambient temperature: 40 °C

    • Design: standing on foot angle




    Typical applications



    • Drive systems for motor drives:


      • Mechanical engineering

      • Elevators / escalators

      • Pipes

      • Conveyor technology

      • Ventilation and air conditioning

      • Robotics

      • Automation technology


    • Power supplies

    • Wind turbines



  • CNW 933

    Three-phase sinusoidal filter

    CNW 933
    • Nominal Voltage: 500 V
    • Rated current: 2 - 1200 A
    • Inductance per strand: 0,05 - 25 mH

    Sinusoidal output current - save costs and trouble-free operation.


    For particularly long cable lengths of > 100m between inverter and motor the shielded cable for EMI suppression used can cause a capacitive coupling. A conventional motor choke can not provide sufficient damping in such cases.


    The sinusoidal filter is a low pass from inductance and capacitance and has a very low resonance frequency. So it is able to generate a largely sinusoidal current. The operation and the loss balance of the asynchronous motor behave like the normal mains operation. The typical motor noise with converter do not occur and a shielded cable to the motor can be dispensed. Losses and heating are greatly minimized and the leakage current will be reduced. Longer motor cable lengths are possible. The motor insulation is protected, thus increasing the service life.


    The sinusoidal filter also attenuates the conducted interference in lower frequency range very good. The losses and the typical noise in the motor plate can be reduced.



    • Rated voltage: U ≤ 3 x 500 V

    • Max. voltage ripple: 5%

    • Field frequency: 0 - 60 Hz

    • Drive switching frequency: up to 150 A >4kHz, from 150 A >1,5KHz

    • Short-circuit voltage Uk: 8% (bei 400V)

    • Voltage drop: 18,4 V/Strang (bei IN und 50Hz)

    • Max. Cable length to the motor: 600 m (unshielded) 1000m (shielded)

    • According to: EN 60289 / EN 61558

    • Test voltage: L-L 2500 V, AC/50Hz 60s; L-PE 2500 V, AC/50Hz 60s

    • Insulation class: T40/F

    • Protection class: IP00

    • Climatic category: DIN IEC 60068-1

    • Overload: 1,5 x INenn 1 min / h

    • Ambient temperature: 40 °C

    • Design: standing on foot angle



    Typical applications



    • Drive systems for motor drives:


      • Mechanical engineering

      • Elevators / escalators

      • Pipes

      • Conveyor technology

      • Ventilation and air conditioning

      • Robotics

      • Automation technology


    • Power supplies

    • Wind turbines

  • CNW M 903

    Fully encapsulated three-phase mains choke 4% Uk

    CNW M 903
    • Nominal Voltage: 500 V
    • Rated current: 3 - 36 A
    • Inductance: 0,81 - 9,8 mH

    The mains chokes in fully encapsulated version are specially designed for rough environments and offer a very good mechanical protection of the component. The fully encapsulation allows design up to protection ratings IP 66.


    Power Noise Reduction - save up to 20% energy costs. A mains choke relieved the supply network by compensating the harmonics reactive power. The harmonics and commutation notches are reduced strongly. By using a mains choke the inverter electronics and DC-capacitors will be protected.


    Starting currents and current peaks are reduced up to 60%. Mains chokes helps to comply with international power quality standards IEEE 519 or EN 61000-3-2.



    • Rated voltage: U ≤ 3 x 500 V 

    • Short circuit: Uk 4% (400VAC/50Hz, INenn)

    • Frequency: 50/60 Hz

    • According to: EN 60289 / EN 61558

    • Test voltage: L-L 2500 V, DC 1min; L-PE 2500 V, DC 1min

    • Insulation class: T40/F

    • Protection ratings: IP00 up to IP66

    • Climatic categorie: DIN IEC 60068-1

    • Overload: 1,5 x INenn 1 min / h


    • Design: mounted on footprint




     


    Typical applications



    • Drive systems for motor drives:


      • Mechanical engineering

      • Elevators / escalators

      • Pipes

      • Conveyor technology

      • Ventilation and air conditioning

      • Robotics

      • Automation technology


    • Power supplies

    • Wind turbines


     

  1. Page:
  2. 1
  3. 2

Downloads

  • Download
    Industrial Converter Solutions - Renewable
    pdf 4.00 KB

    Industrial Converter Solutions - Renewable

    Components for Solar and Wind Power Generation
    Download
  • Download
    Protection Ratings
    pdf 4.00 KB

    Protection Ratings

    Discover our brochure about high protection ratings!
    Download
  • Download
    EMC-Filter Product catalogue
    pdf 4.00 KB

    EMC-Filter Product catalogue

    Product catalogue
    Download
  • Download
    Resistors Product catalogue
    pdf 4.00 KB

    Resistors Product catalogue

    Product catalogue for Resistors
    Download
  • Download
    HF-components Product catalogue
    pdf 4.00 KB

    HF-components Product catalogue

    Product catalogue
    Download
  • Download
    Current and voltage sensors catalogue
    pdf 4.00 KB

    Current and voltage sensors catalogue

    Product catalogue
    Download
  • Download
    Liquid cooled systems catalog
    pdf 4.00 KB

    Liquid cooled systems catalog

    Product catalog for liquid cooled systems
    Download
  • Download
    Components for wind power generation Catalouge
    pdf 4.00 KB

    Components for wind power generation Catalouge

    REO components for wind power generation Safe application for onshore and offshore installations
    Download
  • Download
    Braking resistors Overview
    pdf 4.00 KB

    Braking resistors Overview

    REO Braking- and charging resistors The product range at a glance
    Download
  • Download
    Liquid-cooled components
    pdf 4.00 KB

    Liquid-cooled components

    Liquid-cooled components The product range at a glance
    Download
  • Download
    REO chokes with high protection ratings
    pdf 4.00 KB

    REO chokes with high protection ratings

    REO chokes with high protection ratings Fully encapsulated REO chokes
    Download
  • Download
    REOSOL
    pdf 4.00 KB

    REOSOL

    Chokes for solar applications
    Download